TAP PLASTICS INC -- GENERAL PURPOSE EPOXY PART B  -- 8040-00N043946
<pre>=====================  Product Identification  =====================

Product ID:GENERAL PURPOSE EPOXY PART B
MSDS Date:10/07/1991
FSC:8040
NIIN:00N043946
Kit Part:Y
=== Responsible Party ===
Company Name:TAP PLASTICS INC
Address:6475 SIERRA LANE
City:DUBLIN
State:CA
ZIP:94568
Country:US
Info Phone Num:209-823-0171
Emergency Phone Num:209-823-0171
CAGE:0FCC1
=== Contractor Identification ===
Company Name:TAP PLASTICS INC
Address:6475 SIERRA LANE
Box:City:DUBLIN
State:CA
ZIP:94568
Country:US
Phone:925-829-4889
CAGE:0FCC1

=============  Composition/Information on Ingredients  =============

Ingred Name:MODIFIED AMINE REACTION PRODUCT
Fraction by Wt: < 50%
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:POLYAMIDO AMINE
CAS:6811-71-9
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:SUPP DATA: OF MD IN RESPONSE TO THE REACTIONS OF THE
    PATIENT.
RTECS #:9999999ZZ

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:LD50:(ORAL,RAT) >2140-3990 MG/KG
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:EYE:MAY CAUSE SEV IRRIT W/CORNEAL
    INJURY, WHICH MAY RSLT IN PERM IMPAIRMENT OF VISION, EVEN
    BLINDNESS. VAPS MAY IRRIT EYES. SKIN:MAY CAUSE ALLERGIC SKIN RXN IN
    SUSCEPTIBLE INDIVIDUALS. PRLNGD EXPOSURE  COULD CAUSE SEV INJURY.
    RPTD EXPOSURE MAY CAUSE SKIN IRRIT. SKIN ABSORP:PRLNGD EXPOSURE MAY
    CAUSE RSLT(EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ: IN MATL BEING ABSORBED THRU SKIN IN
    HARMFUL AMTS. INGEST: LOW ACUTE ORAL TOX. INHAL:VAPS MAY CAUSE RESP
    SENSIT/ASTHMA IN SUSCEPTIBLE INDIVIDUALS. EXCESS EXPOSURE MAY CAUSE
    IRRIT TO UPPER RES P TRACT. SYSTEMIC & OTHER EFTS: RPTD EXPOSURES
    MAY CAUSE LIVER & KIDNEY EFTS. RSLTS IN VITRO ("TEST TUBE") (SUPP
    DATA)
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

=======================  First Aid Measures  =======================

First Aid:EYES: IRRIGATION OF EYES IMMED W/WATER FOR 30 MIN & SEEK MED
    ATTN. SKIN: IMMED FLUSH W/WATER FOR @ LST 15 MIN WHILE REMOVING
    CONTAM CLTHG. SEEK MED ATTN. WASH CLTHG BEFORE REUSE. INGEST: DO
    NOT INDUCE	VOMIT. GIVE LARGE AMOUNT OF WATER OR MILK IF AVAILABLE
    AND TRANSPORT TO MEDICAL FACILITY. INHAL: REMOVE TO FRESH AIR IF
    EFT OCCURS. CONSULT MED PERSONNEL. NOTE TO MD: MAY CAUSE
    STRICTURE.(SUPP DATA)

=====================  Fire Fighting Measures  =====================

Flash Point Method:PMCC
Flash Point:200F,93C
Extinguishing Media:FOAM, CO2, DRY CHEMICAL.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
    PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NONE SPECIFIED BY MANUFACTURER.

==================  Accidental Release Measures  ==================

Spill Release Procedures:SOAK UP IN ABSORBENT MATERIAL AND COLLECT IN
    SUITABLE CONTAINERS. RESIDUAL MAY BE REMOVED USING STEAM OR HOT
    SOAPY WATER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:PRACTICE GOOD CAUTION & PERSONNEL
    CLEANLINESS TO AVOID SKIN AND EYE CONTACT. AVOID BREATHING VAPORS
    OF HEATED MATERIAL.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:NONE NORMALLY NEEDED. NIOSH/MSHA APPROVED
    RESPIRATOR APPROPRIATE FOR EXPOSURE OF CONCERN .
Ventilation:GOOD ROOM VENTILATION USUALLY ADEQUATE FOR MOST OPERATIONS.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPD CHEMICAL WORK GOGGLES 
Other Protective Equipment:CLEAN BODY-COVERING CLOTHING SHOULD BE
    NEEDED.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
KEY1;J6.SOL IN H2O: SLIGHTLY TO MOD SOLUBLE. EFTS OF OVEREXP:
    MUTAGENICITY TESTS HAVE BEEN NEGATIVE. FIRST AID PROC:IF LAVAGE IS
    PERFORMED, SUGGEST ENDOTRACHEAL &/OR ESOPHAGOSCOPIC CONTROL. IF
    BURN IS  PRESENT, TREAT AS ANY THERMAL BURN, AFTER DECONTAM. NO
    SPECIFIC ANTIDOTE. SUPPORTIVE CARE. TREATMENT BASED ON JUDGEMENT

==================  Physical/Chemical Properties  ==================

Boiling Pt:B.P. Text:DECOMPOSES
Vapor Pres:< 1 @ 20C
Vapor Density:> 1
Spec Gravity:0.95-1.0
Solubility in Water:SUPP DATA
Appearance and Odor:AMBER COLORED LIQUID. MODERATE AMINE ODOR.

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
ACID, EPOXY RESINS.
Stability Condition to Avoid:EXCESS HEATING OVER LONG PERIODS OF TIME
    CAUSED DECOMPOSITION.
Hazardous Decomposition Products:NITROGEN OXIDES WHEN BURNED.

====================  Disposal Considerations  ====================

Waste Disposal Methods:BURN IN ADEQUATE INCINERATOR OR BURY IN AN
    APPROVED LANDFILL; IN ACCORDANCE WITH LOCAL, STATE AND FEDERAL
    REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.